Current Situation and Analysis of Waste Heat Utilization of Brick and Tile Tunnel Kiln
Category: Company News
2016-02-29 11:11
How to use waste heat correctly
Practice has proved that under the premise of burning bricks and drying bricks, scientific and reasonable use of surplus heat in the kiln can improve the baking speed in the kiln and bring certain economic benefits to the enterprise. The correct understanding and utilization of waste heat should start from the following points:
3.1 determination of waste heat use
First of all, it is necessary to know what to do with the development of waste heat. At present, the main uses of waste heat are: heating and bathing in the factory, heating in the surrounding production and living areas, lithium bromide air conditioning and refrigeration, canteen heat, power generation, etc. Only by clarifying the use of waste heat can we determine which utilization method should be adopted.
3.2 calculated residual heat
Waste heat utilization, as the name implies, is to use the excess heat in the kiln under the premise of meeting the burning brick. The amount of residual heat is affected by many factors, such as the calorific value of raw materials, the burnability, the insulation performance of the top of the kiln wall, the tightness of the kiln car, and the rationality of the exhaust system. Medium and large cross-section tunnel kiln thermal insulation material requirements are more stringent, thermal insulation performance is better, the kiln wall temperature is basically at room temperature; Kiln car processing accuracy is relatively high, sealing is better, the bottom temperature is not higher than 50 ℃, this kind of kiln can provide more heat.
The calorific value of raw materials is not the higher the better. The sintering temperature of sintered bricks such as coal gangue, shale and fly ash is generally controlled within 1050 ℃, and a large number of glass phases will appear inside the products at a higher temperature, resulting in over-burning of the products. The calorific value of raw materials is usually called superthermal roasting when it is 600~750kcal/kg. At this time, the sintering curve can be controlled through certain technical measures to prevent the products from burning and melting. When the calorific value is greater than 750kcal/kg, it is basically impossible to burn bricks, and other raw materials must be added to reduce the calorific value. At present, the problem of high calorific value of raw materials cannot be solved by using more waste heat extraction.
An example of a brick factory in Shandong is given here for your reference. Shandong Energy Group Zhaoguan Coal Mine has built two all-coal gangue brick production lines, with a tunnel kiln section of 6.9 meters and a length of 153.05 meters. The raw materials are as follows:
Table 1 Physical Properties of Raw Materials
Table 2 Chemical composition of raw materials
The relevant production data are:
Kiln density: 240 standard blocks/M3
Incoming interval: 70min/car
Average steam output: 2.5 t/h
Average steam temperature: 158 ℃
Steam pressure: 0.35Mpa
The quality of sintered brick meets the requirements of national standard (GB13544-2011), indicating that the waste heat boiler system does not affect the normal production of tunnel kiln.
3.3 choose a reasonable way to use
Installing a hot water tank is the simplest way to utilize waste heat. It can be installed directly on the top of the cooling section kiln. Considering safety, the water tank is generally not too wide. This way of heat recovery efficiency is relatively low, can provide less heat.
The heat exchanger has higher heat extraction efficiency and less investment. Many tunnel kilns above 4.6 meters are equipped with heat exchangers to solve the heating and staff bath problems of our factory. However, affected by the amount of exhaust air and flue gas temperature, the output of hot water produced by the heat exchanger is not large. The heat exchanger used in the brick and tile tunnel kiln is mainly a fixed tube plate heat exchanger. The flue gas enters the heat exchange tube of the exchanger through the air inlet, and the heat is transferred to the water in the shell through the tube wall. The flue gas and the water exchange in countercurrent, as shown in the figure:
The waste heat boiler is generally used when the waste heat utilization system is installed in the reconstruction and new tunnel kiln in the northern region. A production line with an annual output of 6000~80 million bricks can provide residual heat basically equivalent to the output of a coal-fired boiler with an output of 2.5 t/h. Areas with high heat demand are suitable for installing waste heat boilers. Many brick factories under Shandong Energy Group have installed waste heat boilers. The steam generated by the boilers is connected to the boiler room pipe network in the mining area, which solves the bathing problem of thousands of people in summer and provides heating heat source for the mining area in winter. A brick factory affiliated to COFCO transported the steam generated by the waste heat boiler to the bean products processing workshop for food drying. A coal washing enterprise in Linfen, Shanxi, built a brick factory at the village side and sent the steam generated by the waste heat boiler to the building building in the new countryside free of waste heat boiler, the problem of using heat in two villages was solved.
Waste heat power generation is also a good development direction, but to solve the problem of how to generate electricity when the steam volume and steam pressure are unstable, the input-output ratio must also be considered.
3.4 choose professional design, manufacturing and installation units
Many factors should be considered in the design and installation of waste heat boiler. First, the installation position of each part of the boiler and the structure of the heat receiving pipe should be determined according to the kiln structure. The material and wall thickness of the heat receiving pipe should be determined according to the chemical composition of the raw material. The installation position of the boiler should be selected according to the temperature curve. The installation position of the waste heat boiler cannot affect the normal roasting system. The heat pipe of the waste heat boiler of the tunnel kiln is installed inside the kiln body, and is directly in contact with the kiln roof, kiln wall and high-temperature products. The heat extraction method of heat radiation is used to improve the heat extraction efficiency, but there are also many hidden dangers. Sulfur corrosion, fly ash wear, fouling and other problems will affect the heat recovery efficiency and service life of the heat pipe. If the corrosion-resistant material cannot be reasonably selected and the ordinary water wall tube is selected, once the heat pipe is corroded, the hot water will flow into the kiln, The hot water vaporizes rapidly, and the volume will expand more than 1000 times, which will cause explosion in severe cases.
The drum is installed on the top of the kiln. The rising pipe and the production pipe pass through the kiln wall and the kiln top to connect to the drum. There is a production line to seal all the parts below the drum. It looks like heat preservation and cleanliness. In fact, it is not advisable. This is not convenient to check the pipeline at any time and is not conducive to replacing the pipeline.
The waste heat boiler is a pressure vessel, and its design, production, and installation must be supervised by the special inspection department. It must pass the acceptance before it can be put into use. The boiler management personnel must hold a certificate. The installation of waste heat boiler should be designed by regular units, and qualified units should be selected for manufacturing and installation, and induction training should be provided. A complete waste heat boiler system shall include: demineralized water system, boiler, maintenance platform, monitoring (video, pressure, temperature), steam drum, etc.
4. Conclusion
The development and utilization of the waste heat of the tunnel kiln is in line with the energy saving and emission reduction policy, and can also bring benefits to the enterprise, and can promote the use of mature technology in the industry. The user's choice of waste heat utilization method should proceed from their own actual situation, and can be fully developed and utilized under the premise of conditions and needs.